Fountek FE83, 85 평이 좋습니다
FE83 은 수년전에 Jalbum 에서 2, 3 way 로 개발했습니다.
중요한 대역은 200Hz-5000Hz 입니다 FE85는 제한 없이 자기 실력것 동작하도록 합니다
W6-1139 의 특성이 발표한 것과 "같다면" (매우중요)
Network 없이도 2Way가 가능하다고 봅니다
woofer 통을 잘 tuning (50Hz 정도) 해야 합니다
참고
Fountek FE83, 85 평이 좋습니다
FE83 은 수년전에 Jalbum 에서 2, 3 way 로 개발했습니다.
중요한 대역은 200Hz-5000Hz 입니다 FE85는 제한 없이 자기 실력것 동작하도록 합니다
W6-1139 의 특성이 발표한 것과 "같다면" (매우중요)
Network 없이도 2Way가 가능하다고 봅니다
woofer 통을 잘 tuning (50Hz 정도) 해야 합니다
참고
박사님의 생각이 아주 창의적입니다. Fountek FE85와 Tang Band 6.5인치 서브 우퍼를 사용해 네트워크 필터 없이 스피커를 만드는 것이 아주 재미있을 것 같습니다. Boenicke W8에서 Tang Band 6.5인치 서브 우퍼와 4인치 풀레인지가 필터 없이 소리가 잘 날 수 있어 박사님의 생각이 충분히 실현될 수 있을 것 같습니다.
스피커 통은 자작나무 적층으로 만들어 보고 집성목 밀링 작업으로도 구현해 보고 싶습니다.
Senior Member
I just got a few of these. They seem very good for the money. They are quite heavy, clean construction, and the spade lugs are robust, similar to a large woofer.
The basket openings need breathing room. If you mounted these in a 1" baffle with a plain cylindrical thru-hole, you would just about seal off the back. My test baffle is about 7/16", not real thick, and I still had to put all the rear chamfer on I could to get the response to smooth out.
The measurements are with 2 drivers right next to each other on the test baffle, at 1m and about 2.9v, so a touch over 2w into a 4ohm nominal load. I will post single driver stuff when I have it. First we have FR, five curves (accuracy goes away somewhere below 500):
Same thing with 5 db per div instead of two. Looks better, eh?
Next is THD, same drive level and distance:
And another THD, -20db @ 3" to see the small signal characteristic:
The little THD peak above 1k might be some anomaly in my room or test setup. When I measure with no sweep, I get:
I will be getting T/S on these, but my DATS needs to go back to PE to be checked and possibly replaced, because I cannot get it to work.
These drivers have very good sensitivity for small full range 8 ohm units, and smooth response. Maybe best of all, there is very little high end peaking, none really if you don't care what happens up around 15 k. I need to try some baffle options to see how response is affected.
I will definitely be using these in a project.
John
Tags: None
Seasoned Veteran
Re: Fountek FE85 measurements
looks very nice! Could be a good line array contender.
I think, doo-das on the low end are probably measurement artifacts. Whats the size of your baffle?
I would try to take near field and far field response and merge them.
Senior Member
Re: Fountek FE85 measurements
Roman (did I get that right?), baffle is 4 ft square, with drivers mounted a bit off center. I plan to do more stuff including merges with low end, as time permits. Also some vertical off axis with the 2 drivers.
John
Seasoned Veteran
Re: Fountek FE85 measurements
Sounds good.
It's a nice little driver for $12. Could be used in MTM with efficiency becoming reasonable. Looks like break up is high up around 9khz and well controlled too.
Roman.
Line array가 그럴듯해 보입니다. 한번 해 보고 싶긴한데 이미 스피커가 네쌍 정도이니 Wife Factor 때문에 실현이 어려울 것 같습니다. 이 유닛은 개당 얼마인지요? 16개가 필요한데...
풀레인지 Linear array는 아주 매력적인 스피커임에 틀림 없습니다. 다만 위상 문제를 생각해야 합니다. 스피커간 위상 차이를 보정해 주는 회로가 들어가야 합니다. 위상 보정 회로 없이 스피커 형태를 앞으로 나온 곡선형태로 만들면 위상 문제를 해결할 수 있습니다.
FE88EX가 Tangband 6.5인치 서브우퍼와 음압은 더 맞는 것 같습니다. 실제 포트리플렉스 통에서 음압이 어떤지 확인해 보아야 할 것 같습니다.
저도 같은생각을 했습니다
어런것이 개발이고 만드는 재미입니다. 삽질에 흥미가없으면 발전은없습니다
Boenicke W5 하고 같은 unit 을 사용하지만
제 설계/욕심은 중요 대역 내에 Crossover 자체가 없어서
No phase shift 로 보다 더 자연 스럽게